永利国际-永利总站34-首页

Hello, Welcome Changshou City Peida zipper Co. Ltd website!
金属拉链厂家

Contact us

Changshou QiDian zipper  Co., Ltd.
Contact: Mr. Jiang
Mobile: 13773073903
Landline: 0512-52201106
Fax: 0512-52958210
E-mail: 328508120@qq.com
Website: www.cssqdll.com
Address: Changshu City, Jiangsu Province, Mo East Village East
No. 88 Green Road


6 ways to repair the zipper

Your current position: Home >> News >> Company news

6 ways to repair the zipper

Date of release:2017-11-23 00:00 Source: Click:

6 ways: to deal with the rough or pull the zipper to deal with the wrong teeth to deal with missing teeth or bad teeth zipper pull off how to do Sliding slider on the broken how to deal with bad pull ring Loving clothes zipper broken! This is really a disaster! It does not matter, there are many ways to repair the zipper. The next time this happens, you can follow the steps below. Special zipper

1 pull the zipper to the head. If possible, pull the zip around either side of the zipper, exposing all the teeth.
Try to reveal all the teeth so that the zipper can be pulled back smoothly.

If the zipper is clogged with the fabric of the garment and can not be pulled over, keep it that way and try to deal with it.

2 Rub with toothbrush on the tooth. Rub the tip of the drawing pencil along the zipper's teeth, leaving a layer of pencil on the teeth.
Note that the zipper is a problem because it is the roughest and most in need of lubrication.

However, be sure to draw the entire zipper with a paint brush to lubricate the entire zipper.

If it is clipped to the clothes, as far as possible in the folder to the area below and around the end of some more pencil end. It is also easier to pull some pencils out of the clipped fabric.

Pencil at this time is equivalent to better control of the lubricant.

3 zip pull back and forth. Slowly pull the zip around the lubricated zipper.
If you have a bit of resistance, stop and re-apply some pencils, then continue pulling until it can be pulled from one end to the other.

Do not be too fast, this may give rise to other problems.

If it's stuck on fabric, you need to "swing" the zipper slowly and pull it out gently.

4 if the end of the pencil is not good, for a powerful lubricant.
Other lubricants are soap, candle wax, glass cleaner and lip balm.

Apply the zipper in the same way.

5 Then test. Notice how many times you may have to apply it repeatedly.
method
2 deal with the teeth do not fit

1 try to lubricate the teeth. Sometimes, the teeth are too rough to match, if so, refer to method one.
Apply the pencil over all the faces of the tooth. Try pulling the zipper back and forth to see if you can close it.

If that does not work, try applying a glass cleaner, wax, soap or lipstick.

2 Use a pair of pliers to smooth the curved teeth. Carefully check the teeth to see which is not the same or prominent to it, carefully pliers to pull it back.
Use a small pointed nose pliers to hold the teeth one by one. Otherwise, it is possible that you accidentally broke other normal teeth.

3 pliers to fix the zipper. Zipper sometimes open, not normally closed zipper. Use pliers to pull the top and bottom of the zipper together so that it can grasp the other teeth.
Note that the zipper can not fit so hard that it looks like it is stuck. If the zipper is completely closed, it can not be pulled anymore. Instead, you only have to close it to the extent that you can zip it quickly.

4 Remove the metal zipper at the bottom of the zipper. [2] Occasionally, the clothes get worn for a while and the teeth become less tidy. If this happens, you need to remove the metal tabs on the bottom and align them again.
Use a needle-nose pliers to open the metal tab so that you can remove it from the zipper.

Note that this can only be done if the metal laminate can be touched directly.

5 Put the teeth on the zipper together. Pull the zipper to the bottom of the zipper, and then hand the zipper teeth together. Gently pull the zipper over the teeth to make them each one.
Do not pull the zipper directly. If you do it, it will be hard to get it back.

6 Sew the tail with needlework. Sew at least six needles to replace the metal plate.
Must be stitched solid, or zipper will fall off.

7 Try the zip again. At this point, all the teeth should be able to close tightly, while the zipper intact.
method
3 to deal with the case of missing teeth or bad teeth

1 Check the location of bad teeth or missing teeth. If the location is very close to the end, then still can be repaired, but if close to the beginning, do a good job for zipper psychological preparation. [3]
If the missing tooth is in the last third of the zipper, you can fix it.

If it is in the first two thirds, you should change the entire zipper.

2 Pull the zipper over the bad tooth.
You can pull the zipper to the top or just the bad teeth. As long as the bad teeth above, in fact, what specific location does not matter.


3 Sew a few needles on the bad tooth. Sew at least six needles, thus creating a new end.
You need to sew a few times more, so it's safer.

The new end should be just above the damaged area, so that you can keep more zippers.
Teeth on both sides to be sewn.


4 Check the zipper. The zipper should be pulled all the way to the new end.
method
4 zipper pull off how to do

1 Place the keyring at the zipper tab. Find a metal key ring and attach it to the zipper pull ring.
Note that this is only a temporary solution and can only be used if there are holes in the zipper. It is more suitable for jeans, jackets will not work.

Make sure the key ring is large enough to pass through the hole in the zipper.


2 Of course, you can also use rubber instead of the key ring, the rubber band through the hole in the zipper, and then knot in the hole on it.
The size of the rubber tape should be appropriate so that it can successfully pass through the hole in the zipper.

Rubber band more flexibility, easy to replace.


3 Pull a pull key ring or rubber band. Pull the zipper over and continue pulling the keyring or rubber band.
This prevents the newly installed key ring or rubber band from accidentally falling off. When you start to pull, the ring or the band tightly pull the zipper, the zipper closed.
If this method does not work, you can only change the zipper.
method
5 Slider on the slider is broken how to do [4]

1 buy a new one. If the slider is completely broken, you need to change a new one. The new and old size and style should be similar.
Take a look at the letters below the slider. This is the model of the slider.

When buying a new slider, look for something similar to the old one.


2 Remove the suture at the end of the zipper. Remove the suture at the end of the zipper with a wire cutter, both on both sides.
Do not need to remove too much. The purpose of stitching is to expose the metal tabs at the end of the zipper and the structure at the end. Do not think of removing the entire zipper.

If the jacket or other zipper has exposed the end of the clothes, there is no need for the above steps.


3 Remove the metal patch. You can use a needle-nose pliers open the metal sheet removed.
Be careful to prevent removing too many lines, or accidentally ruining the zipper.


4
Remove the slider from the zipper. Remove the slider from the zipper from the zipper.
If you can not take it off, you can use pliers to open it. But this is likely to rupture the teeth or zipper, so still try to pull it down by hand.


5 Carefully install the new slider. Before pulling the slider up, slide the zipper into the upper opening of the slider first and then let it pass under the slider.
If you have a problem with the safety block, try a pin or sewing needle and carefully pull in the slider.

Make sure the teeth in the slider are snapped together.

Until the end of a closed tooth appears, and then pull up the slider.


6 seam a piece. At the bottom of the zipper seam at least six needles, must be sewn under the slider, a new piece formed.
Metal plate unloaded can not be loaded back, but sewing a few stitches can replace the piece.


7 re-zipper up. According to the original demolition of the zipper back again.
This step is over. The zipper is safe now, and the slider can move smoothly back and forth.
method
6 to deal with broken pull ring

1 Find a small ring or something through the slider. If the pull ring is broken, find a small object to replace it on the line.
Possible items are a metal key ring, a paper clip, a phone cord, a nice pendant or a bracelet. If possible, the best pull ring size and similar.


2 Secure it to the slider. Pass it through the hole in the slider and close.
If you use a key ring, jewelry ring or paper clip, you can slide them into the hole.
If it is a telephone line or a closed loop, it needs to be passed through the opening in the bottom of the slider.

3, like usual zipper. Test just pull the pull ring is good to use, the zipper pull back and forth, the effect should be the same as before the bad.
If the above steps can not solve the problem, you may need to completely replace the zipper. Buy a zipper of the same length and width. Remove the bad zipper with a thread splitter and then sew the new zipper. Resin zipper supplier



Related labels:特殊拉链

service
  • Service
二维码

Scan QR code

share

永利国际|永利总站34

XML 地图 | Sitemap 地图